AQA A Level Physics复习笔记6.2.8 Required Practical: Investigating SHM

Equipment List

• Resolution of measuring equipment:
  • Stopwatch = 0.01 s
  • Metre Ruler = 1 mm

   

SHM in a Mass-Spring System

• The overall aim of this experiment is to calculate the spring constant of a mass-spring system
• This is done by investigating how the time period of the oscillations varies with the mass
  • This is just one example of how this required practical might be carried out

   

Variables

• Independent variable = mass, m
• Dependent variable = time period, T
• Control variables:
  • Spring constant, k
  • Number of oscillations

   

Method

The setup of apparatus to detect oscillations of a mass-spring system

1. Set up the apparatus, with no masses hanging on the holder to begin with (just the 100 g mass attached to it)
2. Pull the mass hanger vertically downwards between 2-5 cm as measured from the ruler and let go. The mass hanger will begin to oscillate
3. Start the stopwatch when it passes the nail marker
4. Stop the stopwatch after 10 complete oscillations and record this time. Divide the time by 10 for the time period (which is the mean)
5. Add a 50 g mass to the holder and repeat the above between 8-10 readings. Make sure the mass is pulled down by the same length before letting go

• An example table might look like this:

Analysing the Results

• The time period of a mass-spring system is given by:

• Where:
  • T = time period (s)
  • m = mass (kg)
  • k = spring constant (N m–1)

   

• Squaring both sides of the equation gives:

• Comparing this to the equation of a straight line: y = mx
  • y = T2
  • x = m
  • Gradient = 4π2 / k

   

1. Plot a graph of T2 against m and draw a line of best fit
2. Calculate the gradient
3. The spring constant, k, is therefore equal to:

• The spring constant can also be found using the Hooke’s Law equation (F = -kx)
• An experiment can be carried out and k found from the gradient of a plot of the force F against the extension x
  • The two values could then be compared

   

SHM in a Simple Pendulum

• The overall aim of this experiment is to calculate the acceleration due to gravity from a simple pendulum
• This is done by investigating how the time period of its oscillations varies with its length
  • This is just one example of how this required practical might be carried out

   

Variables

• Independent variable = length, L
• Dependent variable = time period, T
• Control variables:
  • Mass of pendulum bob, m
  • Number of oscillations

   

Method

1. Set up the apparatus, with the length of the pendulum at 0.2 m
2. Make sure the pendulum hangs vertically downwards at equilibrium and inline directly in front of the needle marker
3. Pull the pendulum to the side at a very small angle then let go. The pendulum will begin to oscillate
4. Start the stopwatch when the pendulum passes the needle marker. One complete oscillation is when the pendulum passes through the equilibrium, then to one amplitude and the other and then back to the equilibrium again (not just from side to side)
5. Stop the stopwatch after 10 complete oscillations and record this time. Divide the time by 10 for the time period (which is the mean)
6. Increase the length of the pendulum by adjusting the string and the wooden block and repeat the above for 8-10 readings. The ruler is used to measure the string and ensure it is measured from the wooden blocks to the centre of mass of the bob. Also, make sure the mass is pulled to the side by the same angle before letting go for the oscillations

• An example table might look like this:

Analysing the Results

• The time period of a simple pendulum is given by:

• Where:
  • T = time period (s)
  • L = length of the pendulum (m)
  • g = acceleration due to gravity (m s–2)

   

• Squaring both sides of the equation gives

• Comparing this to the equation of a straight line: y = mx + c
  • y = T2
  • x = L
  • gradient m = 4π2 / g
  • c = 0

   

1. Plot a graph of T2 against L and draw a line of best fit
2. Calculate the gradient
3. The acceleration due to gravity is equal to:

Evaluating the Experiments

Systematic Errors:

• Reduce parallax error by being at eye level with the marker

Random Errors:

• Record the time taken for 10 full oscillations, then divide by 10 for one period, to reduce random errors
• The oscillations may not completely go from side to side, and end up in a circle. Therefore, keep the amplitudes relatively small (only a few cm) and repeat the readings if they do take a different trajectory
• A motion tracker and data logger could provide a more accurate value for the time period and reduce the random errors in starting and stopping the stopwatch (due to reflex times)
• The equation for the time period of a pendulum bob only works for small angles, so make sure the pendulum is not pulled too far out to the side for the oscillations
• For the mass-spring system, the oscillations may not stay completely vertical. Therefore, keep the amplitudes relatively small (only a few cm) and repeat the reading making sure they are vertical

Safety Considerations

• The suspended masses or pendulum bob could damage the surface if they were to fall. Make sure to keep a soft surface directly below the equipment
• Only pull down the mass and spring system a few centimetres for the oscillations, as larger oscillations could cause the masses to fall off and damage the equipment
• The wooden blocks must be tightly clamped together to hold the string for the pendulum in place, otherwise the pendulum may dislodge during oscillations and fall off

Step 1: Complete the table

Add the extra column T2 and calculate the values

Step 2: Plot the graph of T2 against the mass m

Make sure the axes are properly labelled and the line of best fit is drawn with a ruler

Step 3: Calculate the gradient of the graph

The gradient is calculated by:

Step 4: Calculate the spring constant, k